Manuals

Specifications: Dell 2001FP Flat Panel Color Monitor User's Guide

Specifications: Dell™ 2001FP Flat Panel Color Monitor User's Guide

General • Flat Panel • Resolution • Preset Display Modes • Electrical • Physical Characteristics • Environmental • Power Management Modes • Pin Assignments • Universal Serial Bus (USB) Interface • Plug and Play Capability

General

Model number

2001FP

Flat Panel

Screen type

Active matrix - TFT LCD

Screen dimensions

20.1 inches (20.1-inch viewable image size)

Preset display area:

Horizontal

408 mm (16.1 inches)

Vertical

306 mm (12.1 inches)

Pixel pitch

0.255 mm

Viewing angle

+/- 88° (vertical) typ, +/- 88° (horizontal) typ

Luminance output

250 cd/m ²(typ)

Contrast ratio

400:1

Faceplate coating

Antiglare with hard-coating 3H

Backlight

CCFL (6) edgelight system

Response Time

16ms typical

Resolution

Horizontal scan range

31 kHz to 80 kHz (automatic)

Vertical scan range

56 Hz to 76 Hz, exception 1600 x 1200 at 60 Hz only

Optimal preset resolution

1600 x 1200 at 60 Hz

Highest preset resolution

1600 x 1200 at 60 Hz

Dell guarantees image size and centering for all preset modes listed in the following table.

Preset Display Modes

Display Mode	Horizontal Frequency (kHz)	Vertical Frequency (Hz)	Pixel Clock (MHz)	Sync Polarity (Horizontal/Vertical)
IBM^{?/sup>, VGA1, 720 x 400}	31.5	70.1	28.3	-/+
IBM, VGA3, 640 x 480	31.5	59.9	25.2	-/-
VESA^{?/sup>, 640 x 480}	37.5	75.0	31.5	-/-
VESA, 800 x 600	37.9	60.3	40.0	+/+
VESA, 800 x 600	46.9	75.0	49.5	+/+
VESA, 1024 x 768	48.4	60.0	65.0	-/-
VESA, 1024 x 768	60.0	75.0	78.8	+/+
VESA, 1152 x 864	67.5	75.0	108.0	+/+
VESA, 1280 x 1024	64.0	60.0	108.0	+/+
VESA, 1280 x 1024	80.0	75.0	135.0	+/+
VESA, 1600 x 1200	75.0	60.0	162.0	+/+

Electrical

Video input signals

Analog RGB, 0.7 Volts +/-5%, 75 ohm input impedance

Digital DVI-D TMDS, 600mV for each differential line, 50 ohm input impedance

S-video, Y input 1 volt(p-p), C input 0.286 volt(p-p), 75 ohm input impedance

Composite, 1 volt(p-p), 75 ohm input impedance

Synchronization input signals

separate horizontal and vertical;
3.3V Cmos or 5V TTL level, positive or negative sync.

AC input voltage / frequency / current

90 to 264 VAC / 50 or 60 Hz + 3 Hz / 2.0A (Max.)

Inrush current

110V: 60A (Max.)
220V: 120A (Max.)

Physical Characteristics

Connector type

Signal cable type

D-sub: Detachable, Analog, 15pin, shipped attached to the monitor
DVI-D: Detachable, Digital, 24pin, shipped detached from the monitor S-video: Not included with display Composite: Not included with display

Dimensions (with stand):

Height (fully extended in portrait mode)

635.0 mm (25 inches)

Height (compressed/locked in landscape mode)

457.7 mm (18 inches)

Width

447 mm (17.6 inches)

Depth

245.5 mm (9.67 inches)

Weight

Monitor (Stand and Head)

8.5 Kg (18.72 lb)

Power Supply Brick

0.47Kg (1.03 lb)

Monitor Flat panel only (VESA Mode)

5.45Kg (12.0 lb)

Weight with packaging

11.2Kg (24.63 lb)

Environmental

Temperature:

Operating

5° to 35°C (41° to 95°F)

Nonoperating

Storage: 0° to 60°C (32° to 140°F)
Shipping: -20° to 60°C(-4° to 140°F)

Humidity:

Operating

10% to 80% (noncondensing)

Nonoperating

Storage: 5% to 90% (noncondensing)
Shipping: 5% to 90%(noncondensing)

Altitude:

Operating

3,657.6m (12,000 ft) max

Nonoperating

12,192 m (40,000 ft) max

Thermal dissipation

238.84 BTU/hour (maximum)
187.66 BTU/hour (typical)

Power Management Modes

If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. This is referred to as 'Power Save Mode'*. If input from keyboard, mouse or other input devices is detected by the computer, the monitor will automatically "wake up". The following table shows the power consumption and signaling of this automatic power saving feature:

VESA Modes	Horizontal Sync	Vertical Sync	Video	Power Indicator	Power Consumption
Normal operation	Active	Active	Active	Green	90 W (max. with USB and Soundbar)
Active-off mode	Inactive	Inactive	Blanked	Amber	Less than 3 W Avg.
Switch off	-	-	-	Off	Less than 1 W

Note: The OSD will only function in the 'normal operation' mode. Otherwise one of the following messages will appear depending upon the selected input.

1. Analog Input
In Power Save Mode
Press Any Key on Keyboard or Move Mouse
or
2. Digital Input
In Power Save Mode
Press Any Key on Keyboard or Move Mouse

Activate the computer and 'wake up' the monitor to gain access to the OSD.

3. S-video Input

In Power Save Mode

Please Check Video Signal

4. Composite Input

In Power Save Mode

Please Check Video Signal

Check the video signal and 'wake up' the monitor to gain access to the OSD.

This monitor is ENERGY STAR®-compliant as well as TCO '99/ TCO '03 power management compatible.

* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.

ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, DELL has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

Pin Assignments

15-pin D-sub Connector

Pin Number	15-Pin Side of the Signal Cable
1	Video-Red
2	Video-Green
3	Video-Blue
4	GND
5	Self-test
6	GND-R
7	GND-G
8	GND-B
9	PC5V
10	GND-sync
11	GND
12	DDC data
13	H-sync
14	V-sync
15	DDC clock

24 Pin Digital DVI-D Connector:

Pin Number	24-Pin Side of the Signal Cable
1	TMDS RX2-
2	TMDS RX2+
3	TMDS Ground
4	Floating
5	Floating
6	DDC Clock
7	DDC Data
8	Floating
9	TMDS RX1-
10	TMDS RX1+
11	TMDS Ground
12	Floating
13	Floating
14	+5V Power
15	Self test
16	Hot Plug Detect
17	TMDS RX0-
18	TMDS RX0+
19	TMDS Ground
20	Floating
21	Floating
22	TMDS Ground
23	TMDS Clock+
24	TMDS Clock-

S-video connector

Pin Number	5-Pin Side of the Signal Cable
1	GND
2	GND
3	LUMA
4	CHROMA
5	GND

Composite Connector

Pin Number	1-Pin Side of the Signal Cable
1	LUMA COMPOSITE CHROMA

Universal Serial Bus (USB) Interface

This monitor supports High-Speed Certified USB 2.0 interface.*

	Data Rate	Power Consumption
High speed	480 Mbps	2.5W (Max., each port)
Full speed	12 Mbps	2.5W (Max., each port)
Low speed	1.5 Mbps	2.5W (Max., each port)

USB Upstream connector

Pin Number
4-Pin Side of the Signal Cable

1 VCC

2 DMU

3 DPU

4 GND

USB Downstream connector

Pin Number
4-Pin Side of the Signal Cable

1 VCC

2 DMD

3 DPD

4 GND

USB ports:

1 upstream - rear
4 downstream - 2 on rear; 2 on left side

*Note: USB 2.0 capability requires 2.0 capable computer

Note: *Monitor's USB interface works ONLY when monitor is Powered ON (or in Power Save Mode). Switching your monitor OFF and then ON would re-enumerate its USB interface; attached peripherals may take a few seconds to resume normal functionality.

Plug and Play Capability

You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. If desired, the user can select different settings, but in most cases monitor installation is automatic.

Back to Contents Page